Operating procedures of drifting fish feed maker

1. Running procedures of floating fish feed machine( 1) Safety measures prior to beginning and also after stopping① Inspect all parts of fish feed drifting pellet making maker, particularly the attaching screws and also anchor bolts of each area of the puffing chamber, the linking screws between the electric motor base and also the frame, as well as the screw link between the puffing chamber and also the structure, and there must be no looseness;② Manually revolve the main shaft, right now, there ought to be no massaging audio in the fish feed drifting pellet making device puffing dental caries;③ Beginning the feeding auger of fish feed drifting pellet making maker, check its stepless high-speed performance, as well as call for typical operation;④ Check and also clean the water as well as gas courses before beginning the fish feed drifting pellet making device, and all filters need to be cleansed;⑤ Before starting the fish feed floating pellet making maker, examine whether the wiring of the electric control part is right, whether the turning of each motor is right, and whether the control is reputable;⑥ After the fish feed drifting pellet making device is stopped, you must wear high-temperature handwear covers, quickly eliminate the discharge mold and mildew, and right away tidy it while it is warm, and start the primary motor to empty the product built up in the blowing dental caries. When the corn is puffed, soybean powder need to be included The product is rinsed tidy;⑦ Focus on safety when unloading the maker, as well as do not stand in front of the machine to avoid risk triggered by residual stress in the fish feed floating pellet making machine cavity;⑧ After the fish feed floating pellet making equipment is running generally, it will not be shut down at will.( 2) Power on① Before starting the fish feed floating pellet making device, check the bolts, and also there must be no looseness;② Make certain the regular supply of vapor and also water;③ Make certain that the power supply and electrical appliances are typical;④ Open the heavy steam shutoff, pre-heat the floating fish pellet machine puffing chamber, the temperature level is about 100 levels;⑤ Start the fish feed drifting pellet making equipment: start the conditioner, start the feeding auger, when there is material flowing out from the electrical outlet of the conditioner, begin including vapor to the conditioner.A small amount of water is added, and also the material is fed right into the blowing tooth cavity at the same time. After the product is extruded by fish feed floating pellet making equipment, the puffing impact and wetness of the product are readjusted.( 3) DowntimeAfter the fish feed drifting pellet making machine production concerns an end, it needs to be quit. The quit series is: feeding auger and also conditioner. After that wait till the suggested worth of the main engine current on the electric control closet ends up being the no-load present value, then quit the main electric motor and the oil pump electric motor.( When the corn is blown, regarding 25 kg of soybeans need to be fed into the bypass feeding port of the very first area of the puffing dental caries. To clean up the recurring corn material in the blowing tooth cavity, and after that quit the main electric motor to stop the fish feed drifting pellet making equipment from blocking), after that rapidly dismantle the puffing tooth cavity of the tail section for cleansing.After cleaning, apply oil to the internal wall surface of the major shaft and also screw head (After feeding oil), re-install it and also wait for the following boot;When you see that the material level sign on the silo suggests that the product degree has reached the most affordable degree, start to prepare for shutdown. Currently, do not quit the feeding auger and conditioner, and quit feeding when the major fish feed floating pellet making maker current decreases to the no-load present auger and also conditioner.2. Operation series of drifting fish feed equipment( 1 )When puffing soybeans, both sections at the inlet end of the blowing cavity are single screw heads, as well as the three areas at the electrical outlet end are outfitted with double screw heads.First, add steam to the jacket to preheat the puffing tooth cavity to concerning 100 degrees, and placed the screws on the blowing cavity at the tail section. After the plug is tightened, loosen it for 3-4 turns, and afterwards tighten up the screw plug to repair the screw plug prior to feeding.By controlling the stepless high-speed system of the feeding auger, the feeding rate is from sluggish to fast, and also the feeding speed is from little to large. After the soybean dish is expelled from the screw plug opening, include the cover to go into the typical production, as well as configure the screw connects with various apertures to acquire soybean dish with different returns and also finenesses.By setting up the cone-shaped stress rings of different diameters, the shown temperature of the four-section (discharge end) puffing tooth cavity is 130-140 levels. It is advised that the filter of the crusher utilized for squashing soybeans should have a diameter of 3-4.( 2 )When extruding grainy feed by fish feed floating pellet making maker, the extruding screws in the squeezing out cavity are all single screw heads, include vapor to the jacket to pre-heat the puffing tooth cavity to about 80 degrees, as well as go into the fish feed floating pellet making machine and heavy steam evenly relieved and solidified powder. Regarding 18%, this must be performed in the feed conditioner, as well as the feed amount is controlled by the stepless rate controling device from tiny to huge. Keep in mind that the analysis of the ammeter of the major electric motor need to not surpass the rated present of the main engine of fish feed floating pellet making maker.Beware of overwhelming the motor and also squeezing out fine-grained materials. When the temperature of the extruding chamber at the discharge end is regulated to an proper level by configuring cone-shaped pressure rings with various diameters.The above is the principle, framework and running procedures of the fish feed drifting pellet making device introduced by Richi Equipment. In pursuit of crispy preference and also excellent look, makers often add a leavening agent (or baking powder), which consists of a certain amount of aluminum elements, and generates gas when heated up during cooking or frying, and also the leavening representative is inside the food.